Major components of our Commercial water softeners include our metered control valve, designed to provide greater efficiency; pressure tank; brine tank to contain the water softener salt; ion exchange resin; gravel under bedding to provide even flow distribution; hub and lateral bottom distributor; and water softener salt, used to strip hardness minerals from the resin beads. Systems are manufactured in the USA and assembled in Ocala, Florida. Valves, tanks, resins, filter media and carbons are NSF certified and meet all performance requirements.
Our engineering department is eager to assist you with your commercial and industrial water softener requirements. All water softeners come with USA manufactured valves, NSF certified mineral tanks, gravel under bedding, riser tube, distributor and brine tank. Systems with 1.5”, 2” and 3” valves come with hub and laterals to proper flow distribution. Systems are shipped unassembled on pallet.
The process whereby hardness minerals are removed is described below:
Regeneration cycles are described below:
This is an upward flow to remove any particles which have accumulated in the softener tank and to refresh the resin bed.
This important step is when brine water flows through the resin to remove the hardness minerals. During this cycle, hardness minerals become unattached from the resin and are attracted to the sodium, contained in the brine water.
During this up-flow cycle, salt and hardness minerals are rinsed off the ion exchange resin.
This is an additional cycle to make sure the salt is thoroughly removed from the resin.
During the refill cycle, water is added to the brine tank so there will be a sufficient amount of brine water for the next regeneration cycle.
This is when water flows through the softener to provide soft, conditioned water..
|Valve sizes||1”, 1.25”, 1.5”, 2” and 3”|
|Pipe fittings available||¾”, 1”, 1.25”, 1.5”, 2” and 3”|
|Regeneration method||Down flow|
|Riser tube size||1.05”, 1.25”, 1.5”, 2” and 3”|
|Drain line fitting||¾” male NPT|
|Drain line tubing||½”, ¾” or 1”|
|Brine line||3/8” quick connect|
|Supply voltage||120 V AC|
|Supply frequency||60 Hz|
|Output voltage||12 V AC|
|Operating pressure||20 psi to 125 psi|
|Operating temperature||40°F to 110°F|
|Resin volume (cubic feet)||1.0, 1.5, 2.0, 3.0, 4.0, 7.0 and 10.0|
|Resin type||8% crosslinked std. (10% available)|
|Brine tank volume||240 lbs. (other sizes available)|
|Brine tank overflow||Overflow prevention device Included|
|Model Number||Size Valve||Resin Capacity (Cu. Ft.)||Resin Type||Design Flow Rate (GPM)||Mineral Tank||Brine Tank||Bottom Distributor|
|SW-WC-300-125||1.25”||3||8%||15-20||14X65||18X36||Riser and basket|
|SW-WC-400-125||1.25”||4||8%||20-25||16X65||18X36||Riser and basket|
|SW-WC -400-150||1.5”||4||8%||25-30||16x65||18x36||Hub & laterals|
|SW-WC -700-150||1.5”||7||8%||30-35||21x62||18x36||Hub & laterals|
|SW-WC-700-200||2”||7||8%||35-40||21x62||38x55||Hub & laterals|
|SW-WC-1000-200||2”||10||8%||40-65||24x72||38x55||Hub & laterals|
|SW-WC-2000-200||2”||20||8%||40-90||36X72||38X55||Hub & laterals|
|SW-WC-3500-300||3”||35||8%||40-95||48X72||38X55||Hub & laterals|
|SW-WC-5000-300||3”||50||8%||65-100||63X86||38X55||Hub & laterals|
Top quality equipment and affordable prices, all manufactured in the USA.
We are happy to provide quotations upon request. Please specify the products of interest and be sure to tell us where you reside. Water conditions vary, and we are happy to provide technical assistance.